How To Install Lattice Under a Deck: Achieve a Polished Look
Create a sleek under-decking look by following the right steps
Learning how to install lattice under your deck or porch can give your home a much-needed refresh. To achieve a finished look, it’s best to build a frame for each lattice section before securing it to your home. Here’s how to install lattice under a deck or porch, no matter the height of your space.
Why Install Lattice Under Your Deck or Porch?
While most homeowners are interested in adding lattice under their porch or deck for aesthetic reasons, it can serve a useful purpose, too. Installing lattice skirting under your deck or porch offers these benefits:
Provides a fresh, unified look
Conceals the framing of your house, such as floor joists and posts
Keeps debris out
Creates hidden under-deck storage
Allows for proper air ventilation, keeping your framing dry and rot-free
Prevents animals from living underneath it
How to Prep for Lattice Installation
Amping up your outdoor space with lattice makes for a great weekend project. Tackle a few preparation steps for a smooth DIY: plan your design, buy your lattice, and get your tools ready.
Plan Your Design
For your lattice to look polished, it’s best to frame the sides of each lattice section with 1x4 boards. The framing hides rough edges and forms an intentional design. Study photos of aspirational homes with lattice to create a vision for your own home. Similar to building deck stairs, it’s helpful to draw a rough sketch on a piece of paper to create a design plan.
Choose Your Lattice
Select the type of lattice you want: pressure-treated wood, composite, or synthetic lattice made of vinyl or plastic. Pressure-treated lumber offers a classic look, while composite and synthetic lattice is lower maintenance and more durable.
Lattice comes in a traditional diamond pattern or decorative styles with botanical and leaf designs. You can stain or paint your wood lattice or choose a colored lattice that complements your home’s exterior. Lattice is usually 2 or 4 feet in width and 4 or 8 feet long. Opt for the lattice size that requires the fewest number of cuts for your space.
Determine Your Access Spot
Most local building codes require one access spot under your deck or porch. An access panel also allows you to get under your porch or deck for repairs, cleaning, and storage without detaching a permanent section.
You can create a fully removable section or attach your access panel with a hinge. Decide where your access spot will be—perhaps a more hidden location or one with higher height clearance.
Remove Old Lattice
If you have an existing lattice structure under your deck or porch that’s rotting, outdated, or broken beyond repair, remove each piece with a flat pry bar. Use gentle force so you don’t damage the porch fascia, support columns, or wood surface. You can cut the lattice into pieces with a reciprocating saw and pry off small nails with a carpenter cat's paw. Then, you can prepare to start fresh with a brand-new lattice.
Check for Animals
Before installing lattice, ensure no animals, rodents, bees, or wasps are living underneath your porch or deck. Animals tend to like dry, dark places to nest, so you can humanely get rid of rodents under your deck by running your hose next to the deck and allowing light to enter the space. That should encourage them to leave.
If you're having difficulty relocating animals, contact your local animal control office. Gentle approaches to relocating animals and bees is best, as traps and poison can harm other wildlife.
Protect Yourself and Gather Your Gear
Since you'll be working with a circular saw to cut your lattice, ensure you wear eye protection, ear plugs, and work gloves. You should also check to see if installing lattice requires a building permit in your city or county. Review any building and construction guidelines. Get your tools ready, including a power screwdriver, circular saw, and tape measure.
You’ll also need supplies such as:
Pressure-treated 2x4 boards
Lattice
3½ inch flat corner braces
6-inch mending plates
4-inch T-plates
1 inch panhead galvanized screws
Washers
Gate hardware kit
How to Install Lattice Under Deck
Create a beautiful lattice design you can be proud to show off. From measuring and cutting your lattice to securing the pieces, here’s how to install lattice skirting under your deck or porch.
1. Frame Beneath Your Deck or Porch
Start by constructing solid framing between your deck posts to give your lattice a sturdy structure to adhere to. 4-foot lattice pieces should fit nicely into the framing structures.
Measure the horizontal distance from one deck post to another. Your bottom 2x4 framing member should sit 3 to 4 inches off of the ground to reduce the risk of rot and termites. Cut your 2x4 board, then screw each side in place. If you’re attaching your framing to a concrete foundation or post, use a masonry bit.
Measure the vertical distance from the bottom 2x4 framing member to the underside of the deck. Cut 2x4 framing pieces that will run vertically every 4 feet. Screw the vertical pieces in place, 48 inches on center. Be aware that the height of each vertical 2x4 might differ slightly due to sloping in the ground or deck.
2. Build Your Lattice Frames
For each section of lattice, build a decorative frame with 1x4 boards first. After you build your frames, you'll attach your lattice to the back. Building your frames is easiest when done on a flat surface.
Measure the four sides of your first opening and write it down. You want the lattice to be flush with or tucked behind your deck fascia (the horizontal skirt board) and be flush with the 2x4 framing at the bottom.
Due to ground sloping, the frame might be a rectangle, trapezoid, or other shape. Cut your 1x4s to match the opening (the structural framing can be your guide). If you have two open sections next to each other, create a larger frame that encompasses the whole area (with two or more panels of lattice connected). Cut a 1x4 to be a center stile and attach it in the centerpoint of your frame with 4-inch T-plates. Then, secure the corners of your frame with flat corner braces and mending braces.
3. Attach the Lattice
With a circular saw, cut your lattice piece to fit the frame you built. Your lattice should overlap the backside of the frame by approximately three and a half inches on all sides.
On a flat surface, pre-drill clearance holes in the lattice every 12 inches. The holes should be slightly larger than the screw shanks so the lattice can expand and contract with the weather. Secure the lattice to the back of the frame with galvanized screws driven through washers.
If using a center stile and more than one piece of lattice, secure your lattice to the center stile seam with screws and washers. Your lattice pieces should line up in the middle of the stile on center.
4. Secure the Framed Lattice Panels in Place
Use galvanized screws to attach your finished panels to the framing under your deck or porch. Ask a neighbor or friend to hold the piece while you screw the lattice frame to your structural framing.
5. Create Your Access Spot
The important final step: Making an access spot. For the access panel, use outdoor gate hardware or hinges. Screw the hinges to the frames first, then attach the panel to the deck. A gate hardware kit should include all of the screws and washers needed. Check to make sure the panel swings up and down without issue. You may need to remove some dirt in front of the panel.
Tips for Installing Lattice Under a Deck or Porch
Creating a lattice skirt involves proper measurement and planning. Here are a few tips to make the job easier.
Build your frames first on a flat surface, then attach your lattice to the backside.
Work one section at a time to ensure the lattice panel matches the unique shape and size of that opening.
Double check your measurements before cutting your lumber and lattice to avoid waste.
Consider attaching composite or vinyl lattice pieces first, then adding molding to create a clean finish.
DIY Lattice Installation vs. Hire a Pro
While adding a lattice skirt isn’t as extensive as building a deck, the project could take you a half day or longer, depending on the size of the space, your building experience, and the intricacy of your design. With careful attention to detail, the right tools, and patience, you can install lattice under your deck and get a beautiful, polished result.
But if you’d rather not give up a free weekend or don’t have a circular saw, hire a local deck builder to construct a lattice skirt for you. They can ensure a seamless, sturdy design and likely complete the project faster.
Frequently Asked Questions
Putting lattice under a deck will create a polished look that allows for air ventilation. You can also store items underneath as the lattice provides privacy and protection from the weather. You can also put lattice under a porch to create a polished look in the front of your house.
You secure the bottom of the lattice to a 2x4 framing member, usually 3 to 4 inches from the ground. The lattice is also secured on the side of an existing post or newly framed post. The gap at the bottom of your lattice ensures proper airflow and prevents rot and termites.
Lattice should not touch the ground, as it creates a possibility for rot and a termite infestation. It’s best to leave a gap of 3 or 4 inches at the bottom for airflow and to keep the wood dry. You can add stones, bricks, or other decorative pieces to conceal the bottom of the lattice if desired.